Miscellaneous
Part No. Features VCC ICC GV(dB) Package
PD(mW) IOUT IEP
L88312 SHORT CIRCUIT PROTECT BLOCK FOR LNB

* Wide operating voltage range: 8V~32V
* Low on resistance:320 m[
* Constant current set by external resistor
* Thermal shutdown
8~32V <6mA - SOP-8
- Typ=0.37A -
A2804 Zero Voltage Switch

*Easy operation either through the AC line or a DC supply.
*Supply voltage control.
*Very few external components.
*Symmetrical burst control-No DC current components in the load
circuit
*Negative output current pulse up to 250mA-short circuit protection.
*Reference voltage output
8.2V - - DIP-8 SOP-8
350mW 180mA -
A6966 5 DOT LED Level Meter

* Low Spurious Noise Operation.
* Constant Current Output: IOUT=8mA (Typ.)
* Indication Level Steps: 5dB, 5dB, 3dB, 3dB
* Wide Operating Supply Voltage Range: VCC = 4~ 12V
* Variable Input Amplifier Gain: GV = 0 ~ 20dB
14.0V 5mA 0 ~ 20dB SIP-9
600mW 8mA -
LA2284/A 5-DOT Dual LED Level Meter Driver

*High gain rectifying amplifier included (Gv=26dB)
*Low radiation noise when LED turns on
*Logarithmic indicator for 5-dot LED of bar type
*Constant current output(15mA)
*Wide operating supply voltage
*Not necessary diode or transistor for ALC
*Minimum number of external parts required
3.0V/3.5V ~ 16.0V 8mA 24 ~ 28dB SIP-9 MSOP-10
1100mW 12.0 ~ 22.0mA -
UA8316 IGBT Gate Driver

* A high current can directly drive IGBT
* Can directly control from a microcontroller
Source current: -200mA (max), sink current 1A (max)
* Protect the IGBT gate at power on via a diode
 7.0V ~ 24.0V GATEIN=L 8.8mA - SIP-7
925mW - -
6621 RAM MAPPLING 324 LCD
CONTROLLER FOR I/O gC

* Operating voltage range: 2.4V~5.2V
* External 32.768kHz crystal or 256kHz frequency source input
* Built-in 256kHz RC oscillator
* Internal time base frequency sources
* Two selectable bias (1/2 or 1/3), and three selectable duty LCD
applications (1/2 or 1/3 or 1/4).
* Two selectable buzzer frequencies (2kHz/4kHz)
* Power down command reduces power consumption
* Built-in time base generator and WDT
* Time base or WDT overflow output
* 324 LCD driver
* 8 kinds of time base/WDT clock sources
* Built-in 324 bit display RAM
* 3-wire serial interface
* Software configuration feature
* Internal LCD driving frequency source
* Data mode and command mode instructions
* VLCD pin for adjusting LCD operating voltage
* R/W address auto increment
* Three data accessing modes
2.4V~5.2V - - DIP-28 SSOP-48
- - -
U8C3005 8 BIT SERIAL-IN PARALLEL-OUT VALVE DRIVER

* VDD range: PVDD 8V to 30V
* each channel current limit: 50mA
* Integrated internal 6V regulator
* Maximum clock frequency: 0.5MHz
* Built-in open/short detection
* Short protect
* Detecting response
* Internal reverse diode of PVDD to Absorb reverse current from coil
8.0V~30.0V TYP=3.2mA - SOP-16
1000mW - -
U8C3525 8 BIT SERIAL-IN PARALLEL-OUT VALVE DRIVER

*VDD range: VDD 5V to18V
PVDD 5V to 35V
*Maximum clock frequency: 1MHz
*current limit of Each channel:250mA
*Built-in open/short detection
*Short protect
*Detecting response
*Internal reverse diode of PVDD to Absorb reverse current from
coil
5.0V~18.0V TYP=2.3mA - SOP-16
1000mW 250mA -
U8C3060 8 CHANNEL SERIAL INTERFACE LOW-SIDE DRIVER

* 8 Channel Protected Low-side Driver
   Eight NMOS FETs with Overcurrent Protection
   Integrated Inductive Catch Diodes
   Serial Interface
   Open/Short Load Detection
   Configurable 100% Output Timing
   Configurable PWM Duty Cycle
* Continuous Current Driving Capability
   560 mA (Single Channel)
   200 mA (8 Channels)
   Support Parallel Configuration
* 8 V to 38 V Supply Voltage Range
* Input Digital Noise Filter for Noise Immunity
* Internal Data Read Back Capability for Reliable Control
* Protection and Diagnostic Features
   Overcurrent Protection (OCP)
   Open Load Detection (OL)
   Over Temperature Shutdown (OTS)
   Under Voltage Lockout (UVLO)
   Individual Channel Status Report
   Fault Condition Alarm
5V~38V TYP=3mA - TSSOP-16
- 560mA -
TL2494 CC CONTROL FOR CAR BALLAST

* 6 ~ 40V input
* UVLO
* Open circuit protect
* Overload protect
6.0V~40.0V TYP=14mA - SOP-16
1000mW - -
VF8143 LOW-COST Three-Channel 4TH-ORDER STANDARDDEFINITION VIDEO FILTERS

* Three-Channel 4th-order 8MHz filters for SD video
* Transparent input clamping
* AC-or DC-coupled inputs
* AC-or DC-coupled outputs
* Drives single, +6dB output (150[)
* Drives dual, +6dB output (75[)
* DC-coupled outputs eliminate AC-coupling capacitors
* Single +5V power supply
* Robust 8kV ESD protection
4.75V~5.25V TYP=19mA - SOP-8
- - -
VF8146 LOW-COST SIX-CHANNEL 4TH-ORDER STANDARDDEFINITION VIDEO FILTERS

* Six-Channel 4th-order 8MHz filters for standard-Definition video
* Transparent input clamping
* AC-or DC-coupled inputs
* AC-or DC-coupled outputs
* Drives single, +6dB output (150[)
* Drives dual, +6dB output (75[)
* DC-coupled outputs eliminate AC-coupling capacitors
* Single +5V power supply
4.75V~5.25V TYP=35mA - TSSOP-14
- - -
VF8418 TRIPLE VIDEO DRIVER WITH SELECTABLE HD/SD VIDEO FILTERS FOR RGB OR YUV SIGNALS 4.75V~5.25V TYP=45mA - DIP-16
- - -
USA575 LOW VOLTAGE COMPANDOR

* Operating voltage range from 3V to 7V
* Reference voltage of 100mVRMS=0dB
* 600[ drive capability
* One dedicated summing op amp per channel and two extra
uncommitted op amps
* Single or split supply operation
* Wide input/output swing capability
3.0V~7.0V TYP=4.2mA - SSOP-20N TSSOP-20
- - -
USA575A LOW VOLTAGE COMPANDOR

* Operating voltage range from 3V to 7V
* Reference voltage of 100mVRMS=0dB
* 600[ drive capability
* One dedicated summing op amp per channel and two extra
uncommitted op amps
* Single or split supply operation
* Wide input/output swing capability
3.0V~7.0V TYP=4.2mA - SSOP-20N TSSOP-20
- - -
UCHQ200 USB DEDICATED CHARGING PORT CONTROLLER WITH QC 2.0 FAST CHARGING FUNCTION

* Fully Supports Quick Charge 2.0 specification:
Class A: 5V, 9V, 12V Output Voltage.
Class B: 5V, 9V, 12V, 20V Output Voltage.
* Supports USB DCP Shorting D+ Line to D- Line per USB Battery Charging Specification, Revision 1.2.
* Meets Chinese Telecommunication Industrial Standard YD/T 1591-2009.
* Supports USB DCP applying 2.7V on D+ line and 2.7V on D- line.
* Supports USB DCP applying 1.2V on D+ and D- lines.
* Automatic selection of D+/D- mode for an attached device.
*Compliant with Apple and Samsung devices.
4.0V~6.0V TYP=0.6mA - SOP-8
- 500mA -
UCHQ613 USB DEDICATED CHARGING PORT CONTROLLER

* Supports USB DCP Shorting D+ Line to DV Line per USB Battery
Charging Specification, Revision 1.2 (BC1.2)
* Supports Shorted Mode (Shorting D+ Line to D-Line) per Chinese
Telecommunication Industry Standard YD/T 1591-2009
* Supports USB DCP Applying 2.7V on D+ Line And 2V on D-line (or
USB DCP Applying 2V on D+ Line and 2.7V on DV Line)
* Supports USB DCP Applying 1.2V on D+ and DV Lines
* Automatically Switch D+ and D- Lines Connections for an Attached
Device
* Dual USB Port Controller, UCHQ613
* Operating Range: 4.5V to 5.5V
4.5V~5.5V TYP=0.155mA - SOT-26
- 35mA -
URYD21 300mA BI-DIRECTION RELAY DRIVER

* Supports USB DCP Shorting D+ Line to5 to 36V input
voltage range
* Low Power Consumption (IQ<1uA)
* Input High Level Threshold: 3V, compatible with
* most single chip microcontroller
* Typical Driving Current: 300mA
* Rds(on)=15ohm(Vin=12V, PMOSFET+NMOSFET)
* Rds(on)=10ohm(Vin=20V, PMOSFET+NMOSFET)
* Peak Driving Current: 500mA@Vin=24V
* Environment Temperature: -40XC~85XC
5.0V~36.0V 0.001mA - SOT-26
- 300mA -
ULS4X2 4X2 SWITCH MATRIX WITH TONE/POLARITY CONTROLLER

n DESCRIPTION
The UTC ULS4X2 is a low-cost 4 x 2 switch matrix with tone
detector in a 20-lead QFN package. It is used in RF multiplexing
applications from 200 to 3000 MHz. There is a 4 bit decoder and
tone/polarity detector integrated with RF switch which can reject
DiSEqC control signals. Switch may be used in 50/75 ohm
systems.
Both switch outputs (OP1 & OP2) can independently select any
of the four inputs (HH, HL, VH, VL) or simultaneously select the
same inputs. Note that the switch is bi-directional and input/output
functionality may be interchanged.
3.0V~4.2V TYP=2.0mA - QFN-20(4x4)
- - -
TS2043 4 -WireTouch Panel controller

* Power Supply Voltage: 2.7V ~ 5.5V
* Serial Interface
* 4-Wire Touch Panel Interface
* Embedded Touch Panel Drivers
* 12-Bit AD Converter
* Programmable 8 or 12 Bit Resolution
* Conversion Rate: 125 KHz
* 2 Auxiliary Analog Inputs
* Full Power Down Control
2.7~3.6 300uA  - SSOP-16 
800  -  -
TS20 2.4V, 10uA Analog Temperature Sensor

* Power Supply Voltage:2.4V ~ 5.5V
* 2.5XC Accuracy
* 10uA MAX. Current Consumption
* Temperature Range -55XC to +130XC
* Predictable Curvature Error
* Suitable for Remote Applications
2.4~5.5  -  - SOT-25
 - 10mA  -
UEC1001 AIR FLOW INDUCTION
SWITCH FOR ELECTRONIC
CIGARETTES CONTROL

* System Clock Oscillator
* Ultra Low Static Current (<5gA)
* Output Trigger Mode
2.5V ~ 4.2V <5uA - SOT-23-5
SOT-25
SOT-26
- Typ=5mA -
UEC002* AIR FLOW INDUCTION
SWITCH FOR ELECTRONIC
CONTROL

* Ultra low static current ( < 6gA)
* Standby mode, the chip OUT pin is in high-level state, and the
chip outputs low levels when smoking, which has the function of
backward airflow interference without output.
* Smoking process, the maximum low level output time of chip
OUT pin is 12S and the low output will stop after 12S.
* Over-current protection

2V ~ 5V <6uA - SOT-25
- 2A -
UCM105 CV CONTROLLER WITH
MULTI-PROTECTIONS

* SPS CCCV controller
* CMOS output stage
* 2-OCPs/OVP latch/auto-recovery function
* Low operation current
3.0V ~ 5.5V <0.6mA - SOT-26
350mW - -
UL3880* THREE-RAIL SIMPLE POWER
SEQUENCER

* Qualified for Automotive Applications
* Simple Solution for Sequencing 3 Voltage Rails from a Single Input
Signal
* Easily Cascade up to 3 Devices to Sequence as Many as 9 Voltage
Rails
* Power-Up and Power-Down Control
* Low Quiescent Current of 25gA
* Input Voltage Range of 2.7V to 5.5V
2.7V ~5.5V <80uA - SOT-26
520mW - -
UW6691* 6 DIGIT LCD ALARM WATCH
WITH BLACK LIGHT CONTROL

* Hour, Minute, second, Month and Day normal display
* 6 digit chronogramh: Auto ranging after 30 minutes to hour,
mintue, second, from minute,second,1/100second
* Split operative stopwatch(Accurate to 1/100 second)
* Use selectable 12/24 format & 4 year calendar
* Alarm function with 4 to 5 minutes snooze
* Chime on every hour
* One touch correction of time error within 30 seconds
* Alarm output drivcd by build-in transistor
* Dirdct drive of piezo buzzer
* Oscillating build-in transistor
* Backlight (EL) contro; output
1.2V ~1.8V <1.6uA - Chip-On-Board
- - -
UCS221 1-CH DIFFERENTIAL
SENSITIVITY CALIBRATION
CAPACITIVE TOUCH SENSOR

* 1-Channel capacitive touch sensor with differential sensitivity
calibration
* Low power consumption
* Uniformly adjustable sensitivity
* Sync function for parallel operation
* Three steps sensitivity available without external component
* Open-drain digital output
* Internal power on reset
* Embedded common and normal noise elimination circ
2.5V~5V <70uA - SOT-26
200mW - -
MC14511 BCD-To-Seven Segment Latch/Decoder/Driver
* Low Logic Circuit Power Dissipation
* HighVCurrent Sourcing Outputs (Up to 25 mA)
* Latch Storage of Code
* Blanking Input
* Lamp Test Provision
* Readout Blanking on all Illegal Input Combinations
* Lamp Intensity Modulation Capability
* Time Share (Multiplexing) Facility
* Supply Voltage Range = 3.0V ~ 18V
3V ~ 18V 20uA - DIP-16 SOP-16
- 25mA -
隔壁呻吟太大少妇受不了_宝宝把腿开大点就不疼了图_宝贝放松这才一根手指_第一次玩交换真实经历
<֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <ı> <ı> <ı> <ı> <ı> <ı>