Operational Amplifier
Single Operational Amplifier
Part No. Features Number of
Channels 
VCC VOS(mV)  Slew Rate(V/us) Package
Bandwidth Max Typ
M2107 Single Operational Amplifier

*Operating Voltage (V+/V- =1.0V to3.5V)
*Low Output Saturation: (4Vp-p at single 5V supply)
*V- Shield Plate Between +Input and -Input
*Suitable Pin Arrangement for Application
*Bipolar Technology
1 1.0V ~ 3.5V or 7.0V 6 3 SOT-25
-
M2110 Monaural MIC Amplifier

*Operating voltage: 2.7V~5.3V
*Low operating current: V+=5V, 3.5mA (Typ,)
                                   V+=3.3V, 1.1mA (Typ.)
*Short circuit protection for external MIC.
1 2.7V ~ 5.3V - - SOP-8 TSSOP-8
-
M2125 Single-Supply Operational Amplifier

* Single-Supply Operation
* Low Operating Voltage: 2.7V~20V
* Low Operating Current: 1.0mA (typ.)
* Slew Rate: 1.2V/gs (typ.)
1 2.7V ~ 20.0V 7 1.2 SOT-25 SOT-353
1.2MHz
M2136 Ultra Wide Band, High Slew Rate Single Operational Amplifier

*Input Offset Voltage Balance
*Operating Voltage: 1.35V ~ 6V
*Uitra Wide Band: 200MHz Typ.
*High Slew Rate: 45V/gs Typ.
*Low Operating Current: 0.63mA Typ.
1 1.35V ~ 6V 5 45 SOP-8 TSSOP-8
200MHz 
LM318 High-Speed Single Operational Amplifier

* Unit gain stable (internal frequency compensation)
* 4mV typical input offset voltage
* 30nA typical input offset current
* Input bias current of 250nA (maximum)
* 15MHz bandwidth (small signal)
* 50V/gs slew rate (guarantee)
* Operates voltages of 5V to 20V
* Overload protection for Input and output
* Same pin assignment as general-purpose op amps
1 5.0V ~ 20.0V 10 70 DIP-8 SOP-8 
15MHz
LM321 Low Power Single Operational Amplifier

* Low supply current 430gA
* VCC=5V, TA=25XC. Typical values unless specified.
* Gain-Bandwidth product 1MHz
* Low input bias current 45nA
* Wide supply voltage range +3V~+32V
* Stable with high capacitive loads
1 3V ~ 32V 7 0.4 SOT-23-5 SOT-25
1MHz
TS321 Low Power Single Operational Amplifier

* Wide Power-Supply Range
   Single Supply: 3V~30V or Dual Supply: 1.5V~15V
* Large Output Voltage Swing: 0V~3.5V (Min.) (VCC=5V)
* Low Supply Current: 500gA (Typ.)
* Low Input Bias Current: 20nA (Typ.)
* Low Input Offset Voltage: 4mV (Max.)
* Stable With High Capacitive Loads
1 Single Supply: 3V~30V
Dual Supply: 1.5V~15V
4 0.4 SOT-25
0.8MHz
OP07C Very Low Offset Voltage Single Operational Amplifier

* Low Noise
* No External Components Required
* Replace Chopper Amplifiers at a Lower Cost
* Wide Input-Voltage Range: 0 to 14V (Typ.)
* Wide Supply-Voltage Range: 3V to 18V
1 3V ~ 18V 0.06
(TY)
0.3 SOP-8
DIP-8
0.6MHz(TY)
CA3080 * Slew Rate (Unity Gain, Compensated): 50V/gs
* Adjustable Power Consumption: 10
gW~30gW
* Flexible Supply Voltage Range:
2V~ 15V
* Fully Adjustable Gain: 0 to gMRL Limit
1 2V~ 15V 2 50 DIP-8
2MHz
LM741* General-Purpose Single Operational Amplifier 1 2.0V ~ 22.0V @ @ DIP-8 SOP-8 
1MHz
MC336* PLC ANALOG LOW NOISE AMPLIFIER

* Operates from 2.5V to 6.0V Supply
* Low Drain Current 1.3mA Typical @ VDD=5.0Vdc
* Low Number of External Parts Required
* Operating Frequency Up to 60MHz
1 2.5V~6V - - MSOP-8
-
Dual Operational Amplifier
Part No. Features Number of
Channels 
VCC VOS(mV)  Slew Rate(V/us) Package
Bandwidth Max Typ
MC1458 Dual Operational Amplifier

* Low power consumption
* Wide input voltage range
* No latch-up
* High gain
* Short-circuit protection
* Frequency compensation is unnecessary
2 22.0V 5 0.8 DIP-8 SOP-8 
1MHz 
M2100 Dual Operational Amplifier

* Single Supply Operation
* Operating Voltage (1.0V~3.5V)
* Low Saturation Output Voltage
* High Slew Rate (4V/gs typ.)
* Bipolar Technology
2 1.0V ~ 3.5V or 7.0V 6 4 DIP-8 SOP-8 TSSOP-8
12MHz  
M2115 Dual Operational Amplifier

* Operating Voltage: 1V ~7V
* Low Saturation Output Voltage: 2.0Vp-p@V+=2.5V
* Slew Rate: 4V/gs (typ.)
* Unity Gain Bandwidth: 12MHz (typ.)
2 1.0V ~ 7.0V 6 4 DIP-8 SOP-8 TSSOP-8
12MHz 
UM2122 Ultra Low Noise Dual Operational  Amplifier

* Operating Voltage: 2.0V ~ 8.0V
* Ultra Low Noise Voltage: 1.5nV/Hz (typ.) @ f=1kHz.
* Low Saturation Output Voltage: 0.3V (typ.)
* Bipolar Technology
2  2.0 ~ 8.0V 6 2 SOP-8 
12MHz
M2904 Low Power Dual Operational Amplifier

*Single Supply
*Operating Voltage: +3V~+32V
*Low Operating Current: 0.7mA (typ.)
*Slew Rate: 0.5V/gs (typ.)
2 1.5V ~ 16.0V or 3.0V ~ 32.0V  7 0.5 DIP-8 SOP-8 TSSOP-8
MSOP-8
0.2MHz
3308 Dual High Current Operational Amplifier

*Single Supply
*Operating Voltage (+3V~+15V) (1.5V~7.5V)
*High Output Current (150mA)
*High Frequency Noise Rejection
*Internal Enhanced Frequency Compensation
2  1.5V ~ 7.5V or 3.0V ~ 15.0V 5 1 DIP-8 SOP-8 TSSOP-8
1.3MHz
MC33078 Dual Low Noise Operational Amplifiers

* Dual supply operation from: 5.0 V to 18 V
* Low input offset voltage: 0.15mV
* Large output voltage swing: +14.1V/ -14.6V
* High slew rate: 7.0V/gs
* Low voltage noise: 4.5nV/ Hz
* Low total harmonic distortion: 0.002%
* High gain bandwidth product: 16MHz
* High open loop AC gain: 800 @ 20kHz
2 5.0 V to 18 V 2 7 SOP-8 
16MHz 
MC33178 High Output Current Low Noise, Low Power Operational Amplifiers

* Dual supply operation from 2V to 18V
* High slew rate: 2.0V/gs
* Large output voltage swing
* 600[ output drive capability
* Low offset voltage: 0.15mV (Mean)
* Low total harmonic distortion:
   0.0024% (@ 1.0 kHz w/600[ load)
* High gain bandwidth: 5.0MHz
2 2V to 18V 3 2 DIP-8 SOP-8 
5MHz 
MC33272 Single Supply, High Slew Rate, Low Input Offset Voltage Operational Amplifiers

* Single (or dual) supply operation from +3 V to +36V
   (1.5V~18V)
* Large output voltage swing: +14.1V/-14.6V
* Input offset voltage trimmed to 100gV (Typ)
* Very low input bias current: 300nA
* Very low input offset current: 3.0nA
* High input resistance: 16M[
* High slew rate: 10V/gs
* High gain bandwidth product: 24MHz @ 100kHz
* Low total harmonic distortion: 0.003%
* Power supply drain current: 2.15mA per amplifier
* Low noise: 18nV / Hz @ 1.0kHz
2 +3 V to +36V 1 10 SOP-8 
24MHz 
MC34072 High Slew Rate, Wide Bandwidth,Dual Operational Amplifier

* Wide bandwidth: 4.5 MHz
* High slew rate: 13V/gs
* Fast settling time:1.1gs to 0.1%
* Wide single supply operation: 3.0V to 44V
* Wide input common mode voltage range:
   Includes ground (VEE)
* Low input offset voltage: 3.0mV maximum
* Large output voltage swing:
   -14.7V to +14V (with +-15V supplies)
* Large capacitance drive Capability: 0pF to 10,000 pF
* Low total harmonic distortion: 0.02%
* Excellent phase margin: 60X
* Excellent gain margin: 12dB
* Output short circuit protection
2 1.5V ~ 22.0V or 3.0V ~ 44.0V 3 10 DIP-8 SOP-8 TSSOP-8
MSOP-8
4.5MHz
Dual Operational Amplifier
Part No. Features Number of
Channels 
VCC VOS(mV)  Slew Rate(V/us) Package
Bandwidth Max Typ
3404 Dual Operational Amplifier

*Single Supply
*Operating Voltage: +4v~+36v
*Low Operating Current: 2.0mA (Typ.)
*Slew Rate: 1.2v/ms (typ.)
2  2.0V ~ 18.0V or 4.0V ~ 36.0V   5 1.2 DIP-8 SOP-8 TSSOP-8
1.2MHz
3414 Dual High Current Operational Amplifier

* Single supply
* Operating voltage: 3V~15V
* High output current: 70Ma
* Slew rate: 10V/gA(Typ.)
* Bipolar technology
2  1.5V ~ 7.5V or 3.0V~ 15.0V 5 1 DIP-8 SOP-8 TSSOP-8
1.3MHz
3422 High Performance Dual Operational Amplifier

* Single Supply Operation: 3V ~ 36V
* Dual Supply Operation: 1.5V ~ 18V
* High Gain Bandwidth Product: 25MHz
* High Slew Rate: 15V/gs
* Low Voltage Noise: 14nV/Hz
* No Phase Inversion
* ESD Tolerance: 2KV
* Latch-Up Immunity
2  1.5V ~ 18.0V or 3.0V ~ 36.0V  2.5 15 DIP-8 SOP-8 DFN3030-8
25MHz
LM358 Low Power Dual Operational Amplifier

*Internally frequency compensated for unity gain.
*Wide power supply range 3V - 32V.
*Input common-mode voltage range include ground.
*Large DC voltage gain.
2 3.0V ~ 32V   or 16V 5 - DIP-8 SOP-8 SIP-9
MSOP-8 TSSOP-8 DFN2020-8
-
MC4556 Dual High Current Operational Amplifier

* Operating Voltage (2V~18V)
* High Output Current (IOUT=70mA)
* Slew Rate (3V / ms typ.)
* Gain Band Width Product (8MHz typ.)
* Bipolar Technology
2 2.0V ~ 18.0V 6 3 DIP-8 SOP-8 
8MHz
MC4558 Dual Wide Bandwidth Operational Amplifier

* No frequency compensation required
* No latch-up
* Large common mode and differential voltage range
* Parameter tracking over temperature range
* Gain and phase match between amplifiers
* Internally frequency compensated
* Low noise input transistors
2 22.0V 6 2.2 DIP-8 SOP-8 TSSOP-8
SIP-8 SIP-9 MSOP-8
2.8MHz
MC4560 Dual Operational Amplifier

*Operating Voltage (4V~18V)
*Wide Gain Bandwidth Product. (10MHz typ.)
*Slew Rate (4V / gs typ.)
*Bipolar Technology
2 4.0V ~ 18.0V 6 4 DIP-8 SOP-8 MSOP-8
10MHz
M4565 Dual Operational Amplifier.

* Operating Voltage: 4V~18V
* Wide Gain Bandwidth Product: 4MHz (typ.)
* Slew Rate: 4V/gs (typ.)
2 4.0V ~ 18.0V 3 4 DIP-8 SOP-8 TSSOP-8
10MHz 
MC4580 Dual Operational Amplifier

*Operating voltage (2V ~ 18V)
*Low input noise voltage (0.8gVrms typ.)
*Wide gain bandwidth product (15MHz typ.)
*Low distortion (0.0005% typ.)
*Slew rate (5V/gs typ.)
*Bipolar technology
2 2.0V ~ 18.0V 3 5 DIP-8 SOP-8 TSSOP-8
MSOP-8 DFN2030-8 SIP-8
15MHz 
LM833 Low Noise Dual Operational Amplifier

* High slew rate: 7V/gs
* High gain bandwidth product: 15MHz
* Excellent frequency stability
* Low distortion: 0.002%
* Low voltage noise: 4.5nV/Hz
2  2.5V ~ 15.0V or 5.0V~ 30.0V 5 7 SOP-8 
15MHz
LM224 Quad Operational Amplifier

* Wide Supply Voltage Range. (Single Supply: 3~30V)
* Low Supply Current Drain Independent of Supply Voltage: 0.8 mA Typ
* Large DC voltage gain: 100dB
* Input Common-Mode Voltage Range Includes Ground.
* Low Input Bias and Offset Parameters
* Differential Input Voltage Range Equal to Maximum Rated Supply Voltage: 32V
* Open-Loop Differential Voltage Amplification: 100 V/mV Typ
* Internal Frequency Compensation for Unity Gain
4 3.0V ~ 30.0V 5 - DIP-14 SOP-14 TSSOP-14
-
LM324 Low Power Quad Operational Amplifier

*Internally frequency compensated for unity gain.
*Large DC voltage gain :100dB.
*Wide operating supply range (Vcc=3V~32V).
*Input common-mode voltage includes ground.
*Large output voltage swing: From 0V to Vcc-1.5V.
*Power drain suitable for battery operation.
4 3.0V ~ 32V or 16V 5 - DIP-14
SOP-14 TSSOP-14
QFN-16(33)
-
MC34074 High Slew Rate, Wide Bandwidth, Quad Operational Amplifier

* Wide bandwidth: 4.5MHz
* High slew rate: 13V/gs
* Fast settling time:1.1gs to 0.1%
* Wide single supply operation: 3.0V to 44V
* Wide input common mode voltage range:
   Includes Ground (VEE)
* Low input offset voltage: 3.0mV maximum
* Large output voltage swing:
   -14.7V to +14V (with +-15V supplies)
* Large Capacitance Drive Capability: 0pF to 10,000pF
* Low total harmonic distortion: 0.02%
* Excellent phase margin: 60X
* Excellent gain margin: 12dB
* Output short circuit protection
* ESD Diodes/Clamps provide input protection 
4 3.0V ~ 44.0V or 22.0V 5 - DIP-14 SOP-14 
4.5MHz
Dual Operational Amplifier with JFET Input
Part No. Features Number of
Channels 
VCC VOS(mV)  Slew Rate(V/us) Package
Bandwidth Max Typ
TL062 Low Power Dual J-FET Operational Amplifier

* Very low power consumption
* Wide common-mode (up to Vcc+ ) and differential voltage range
* Low input bias and offset current
* Output short-circuit protection
* High input impedance J-FET input stage
* Internal frequency compensation
* Latch up free operation
* Typical supply current: 400gA
2 18.0V 15 1.1 DIP-8 SOP-8 TSSOP-8
1MHz
TL072 Low Noise Dual J-FET Operational Amplifier

*Low power consumption
*Wide common-mode (up to Vcc+ ) and differential voltage range
*Low input bias and offset current
*Low noise en = 15nV / Hz (typ)
*Output short-circuit protection
*High input impedance J-FET input stage
*Low harmonic distortion:0.01%(typ)
*Internal frequency compensation
*Latch up free operation
*High slewrate:16V/us(typ)
2 18.0V 10 16 DIP-8
SOP-8
TSSOP-8
4MHz
TL082 General Purpose Dual J-FET Operational Amplifier

* Low input bias and offset current
* Wide common-mode (up to Vcc+) and differential voltage range
* Output short-circuit protection
* High input impedance J-FET input stage
* Internal frequency compensation
* Latch up free operation
* High slewrate:16V/gs(typ.)
2 18.0V 10 16 DIP-8
SOP-8
TSSOP-8
4MHz 
Quad Operational Amplifier with JFET Input
Part No. Features Number of
Channels 
VCC VOS(mV)  Slew Rate(V/us) Package
Bandwidth Max Typ
TL074 Low Noise Quad J-FET Operational Amplifier

*Low power consumption
*Wide common-mode (up to Vcc+ ) and differential voltage
range
*Low input bias and offset current
*Low noise eN = 15nV / Hz(typ)
*Output short-circuit protection
*High input impedance J-FET input stage
*Low harmonic distortion:0.01%(typ)
*Internal frequency compensation
*Latch up free operation
*High slewrate:13V/gs(typ)
4 18.0V 6 13 DIP-14 SOP-14
3MHz
TL084 Low Noise Quad J-FET Operational Amplifier

*Low power consumption
*Wide common-mode (up to Vcc+) and differential voltage range
*Low noise eN = 15nV / Hz(typ)
*Output short-circuit protection
*High input impedance J-FET input stage
*Low harmonic distortion:0.01%(typ)
*Internal frequency compensation
*Latch up free operation
4 18.0V 15 - DIP-14 SOP-14 TSOP-14
1MHz
Low Voltage Rail to Rail Output Single Operational  Amplifier 
Part No. Features Number of
Channels 
VCC VOS(mV)  Slew Rate(V/us) Package
Bandwidth Max Typ
LV2460_LV2461 Family Of Low-Power Rail-To-Rail Input/Output Operational Amplifiers With Shutdown

* Rail-to-Rail Output Swing
* Gain Bandwidth Product: 6.4 MHz
* 80mA Output Drive Capability
* Supply Current: 500gA
* Input Offset Voltage: 100gV
* Input Noise Voltage: 11nV/Hz
* Slew Rate: 1.6V/gs
* Universal Operational Amplifier
* Micropower shutdown mode (LV2460) 0.3gA
1 2.7V~6.0V 2 1.6 SOT-25
SOT-26
SOP-8
6.4MHz
LV321 Low Voltage Rail to Rail Output Operational Amplifier

* 2.7V and 5V Performance Guaranteed
* No Crossover Distortion
* 130gA Low Supply Current
* Rail-to-Rail Output Swing @10k[ Load: V+ -10mV
                                                            V- +65mV
* VCM From -0.2V to V+ -0.8V
1 2.7V~5.5V 7 0.8 SOT-25 SOT-353
1MHz
LLV321 Low Voltage Rail to Rail Output Operational Amplifier

* Input Voltage Varies From -0.25V to +1.5V
* Supply Current: 80gA
* Output Voltage Varies from 0.01V to 2.69V
* Gain Bandwidth: 1.2MHz
* Slew Rate: 1.5V/gs
* Fully Specified at +2.7V and +5V Supplies
* Operating Temperature Range: -40XC ~ +125XC
* Halogen Free
1 2.7V~5.5V 7 1.5 SOT-353
1.2MHz
ULV3211 Rail to Rail Output and High Slew Rate OP AMP

* Single-Supply Operation: +3V ~ +5.5V
* Input / Output Rail-to-Rail
* Low Quiescent Current: 500gA @ 5V
* With Low Input Current
* 5.23V/gs High Slew Rate
* High Output Driving Capacity
* 6.5MHz High Gain-Bandwidth Product
* 70dB High PSRR
1 3.0V~5.5V 10 5.2 SOT-25
6.5MHz
ULV335 ZERO-DRIFT, SINGLE-SUPPLY CMOS OPERATIONAL AMPLIFIERS

* Low offset voltage: 1gV (typ)
* Single-supply operation
1 2.7V ~ 5.5V 20uV 1.6 SOP-8
SOT-25
2MHz
Low Voltage Rail to Rail Output Single Operational  Amplifier 
Part No. Features Number of
Channels 
VCC VOS(mV)  Slew Rate(V/us) Package
Bandwidth Max Typ
ULV3541 220MHz, Rail-to-Rail I/O,CMOS Operational Amplifier

* 2.5V to 5.5V Single Supply or 1.25V to 2.75V
Dual Power Supplies
* Quiescent Current: 4.5mA/Amplifier (TYP)
* Wide Bandwidth: 100MHz GBP
* Unity-Gain Bandwidth: 220MHz
* Rail-to-Rail Input and Output
* High Slew Rate: 160V/gs
* High Output Current: 150mA (TYP)
* Thermal Shutdown
1 2.5~5.5V 10mV 170 SOP-8 
220MHz
ULV6001 Low Power Rail-To-Rail Input / Output OP AMP

* Rail-to-Rail Input/Output
* Supply Voltage: 1.8V~5.5V
* Quiescent Current: 100gA (typ.)
1 1.8V ~ 5.5V 7 0.9 SOT-25 SOT-23-5
1.5MHz
Low Voltage Rail to Rail Output Single Operational  Amplifier 
Part No. Features Number of
Channels 
VCC VOS(mV)  Slew Rate(V/us) Package
Bandwidth Max Typ
ULV7011 Low-Power Tiny Single CMOS Operational Amplifier

* CMOS Technology
* Wide Operating Voltage (VDD=1~5.5V)
* Wide Output Swing Range (VOM=2.9V min. @ 3.0V)
* Low Operating Current
* Slew Rate (0.15V/gs typ.)
* Unity Gain Bandwidth (0.4MHz typ.)
* Internal Compensation Capacito
1 1~5.5V 10 0.15 SOT-25
0.4MHz
ULV7012 Low-Power Tiny Single CMOS Operational Amplifier

* CMOS Technology
* Wide Operating Voltage (VDD=1~5.5V)
* Wide Output Swing Range (VOM=2.9V min. @ 3.0V)
* Low Operating Current
* Slew Rate (1.5V/gs typ.)
* Unity Gain Bandwidth (1.2MHz typ.)
* Internal Compensation Capacitor
1 1~5.5V 10 1.5 SOT-25
1.2MHz
ULV7013 Low-Power Tiny Single CMOS Operational Amplifier

* CMOS Technology
* Wide Operating Voltage (VDD=1~5.5V)
* Wide Output Swing Range (VOM=2.9V min. @ 3.0V)
* Low Operating Current
* Slew Rate (2.5V/gs typ.)
* Unity Gain Bandwidth (1.8MHz typ.)
* Internal Compensation Capacitor
1 1~5.5V 10 2.5 SOT-25
1.8MHz
ULV8538 Low Power Precision Auto-Zero OP AMPS

* Single-supply operation: 2.7V~5.5V
* Low supply current: 180gA
* Low offset voltage: 13gV maximum
* High gain, CMRR, and PSRR
* Qualified for automotive applications
1 2.7~5.5V 13uV 0.4 SOT-25
SOP-8 
430KHz
ULV8551 ZERO-DRIFT, SINGLE-SUPPLY,RAIL-TO-RAIL INPUT/OUTPUT CMOS OPERATIONAL AMPLIFIERS

* Single-supply operation: 2.7V~5.0V
* Low offset voltage: 1gV
* Rail-to-rail input and output swing
* No external capacitors required
1 2.7V ~ 5.0V 20uV 0.3 SOP-8
1.2MHz
ULV341* Low-Voltage Rail-T0-Rail Output CMOS Operational Amplifiers With Shutdown

* 1.8V and 5V Performance
* Rail-to-Rail Output Swing
* Wide Common-Mode Input Voltage Range: -0.2V to (V+- 0.5V)
* Input Offset Voltage: 0.3mV (Typical)
* Gain Bandwidth: 2.3MHz (Typical)
* Slew Rate: 0.9V/gs (Typical)
* Turnon Time From Shutdown: 5gs (Typical)
1 1.5V~5.5V 4 0.9 SOT-26
2.2MHz
LV651* 12 MHz, LOW VOLTAGE, LOW POWER AMPLIFIERS

* Typical 5V Supply, Unless Otherwise Noted
* Specified 3V and 5V Performance
* Low Power Supply Current: 116gA
* Maximum Input Offset Voltage: 1.5mV
* Output Swing With 2k[ Load, 120mV from Rail
1 2.7V~5.5V 3 1.5 SOT-25
12MHz
LV715* LOW-POWER, RAIL TO RAIL INPUT AND OUTPUT, HIGH OUTPUT CURRENT DRIVE
OPERATIONAL AMPLIFIER WITH SHUTDOWN

* Low Offset Voltage: 3mV (Maximum)
* Rail-to-Rail Input and Output
* Capable of Driving 600[ Load
* Ensured 2.7V and 5V Performance
* Supply Current in Shutdown Mode: 0.2gA (Typical)
* Slew Rate: 5V/gs (Typical)
1 2.7V~5.0V 3 5 SOT-26
5MHz
LV721* Low Voltage Rail to Rail Output Operational Amplifier

* Guaranteed 2.2V and 5.0V Performance
* Low Supply Current 930gA (V+=2.2V)
* Rail-to-Rail Output Swing
600[ load 120mV from either rail at 2.2V
2k[ load 50mV from either rail at 2.2V
* Input Common Mode Voltage Range Includes Ground
1 2.2V~5.5V 3 5.25 SOT-25
10MHz
LV821* 5MHz Low Voltage Rail to Rail Output Operational Amplifier

* Guaranteed 2.5V, 2.7V and 5V Performance
* Maximum VOS: 3.5mV
* GBW product : 5MHz V+=2.7V
* Iq : 220gA V+=2.7V
* Minimum SR: 1.4 V/gs
* Rail-to-Rail Output Swing:
   -600[ Load: 160mV from rail
   -10k[ Load: 55mV from rail
* VCM: -0.3V ~ 4.3V V+=5V
1 2.5V~5.5V 3.5 2 SOT-25
5MHz
LV981* SINGLE LOW-POWER 1.8V RAIL TO RAIL INPUT AND OUTPUT OPERATIONAL AMPLIFIERS WITH SHUTDOWN

* Ensured 1.8V, 2.7V, and 5V Specifications
* Output Swing:
   -600[ Load: 80mV from Rail
   -2k[ Load: 30mV from Rail
* VCMR: 200mV Beyond Rails
* Supply Current : 100gA
* Maximum VOS: 4mV
1 1.8V~5.0V 4 0.35 SOT-26
1.4MHz
Low Voltage Rail to Rail Output Dual Operational  Amplifier 
Part No. Features Number of
Channels 
VCC VOS(mV)  Slew Rate(V/us) Package
Bandwidth Max Typ
ULV2262 400gA, 0.71MHz Rail-To-Rail Operational Amplifiers

* Output Swing Includes Both Supply Rails
* Low Noise: 12nV/Hz (Typ.) at f =1kHz
* Fully Specified for Both Single-Supply and Split-Supply
   Operation
* Low Power: 550gA (Max.)
* Common-Mode Input Voltage Range Includes Negative Rail
* Wide Supply Voltage Range: 2.7V~ 6.5V
2 2.7V~6.5V 950uV 0.8V/us SOP-8
0.71MHz
OPA2336 Single-Supply Micropower CMOS Operational Amplifier

* Operating on a Single-Supply
* Rail-to-Rail Output (Accuracy: 3mv)
* Low Power Dissipation: IQ=20gA/Amplifier
* Low Offset Voltage up to 125gV (MAX.)
* Power Supply Specified from 2.3V to 5.5V
* Halogen Free
2 2.3V~5.5V 0.125 0.03 SOP-8
100KHz
ULV2362 High-Performance Low-Voltage Operational Amplifiers

* Low Supply-Voltage Operation: VCC=1V (Min.)
* Wide Bandwidth: 7MHz (Typ.) at VCC=2.5V
* High Slew Rate: 3V/gs (Typ.) at VCC=2.5V
* Low Noise: 8nV/ Hz (Typ.) at f=1kHz
* Wide Output Voltage Swing: 2.4V (Typ.)
   at VCC=2.5V, RL=10 k[
2 1 ~ 2.5 6 3 SOP-8
7MHz
LV2462-LV2463 Family Of Low-Power Rail-To-Rail Input/Output Operational Amplifiers With Shutdown

* Rail-to-Rail Output Swing
* Gain Bandwidth Product: 6.4 MHz
* 48mA Output Drive Capability(VCC=5V)
* Supply Current: 500gA/channel
* Input Offset Voltage: 100gV
* Input Noise Voltage: 11nV/ Hz
* Slew Rate: 1.6V/gs
* Universal Operational Amplifier
* Micropower shutdown mode (LV2463)0.3gA/channel
2 2.7V ~ 6V  2 1.6 SOP-8 MSOP-8
MSOP-10
5.2MHz
LV2622 Low Voltage Rail to Rail Output Operational Amplifier

* Low Cost
* Rail-to-Rail Output Swing
* Input Rail: - 0.1V~+5.6V with VS=5.5V
* Typical VOS: 0.7mV
* Gain-Bandwidth Product: 3MHz
* High Slew Rate: 1.7V/gs
* Settling Time to 0.1% with 2V Step: 2.1gs
* Overload Recovery Time: 1gs
* Low Noise Voltage: 12nV/ Hz
* Operates on 2.5V~5.5V Supplies
* Low Power: 250gA/Amplifier Typical Supply Current
2 2.5V ~ 5.5V 3 1.7 SOP-8 MSOP-8 TSSOP-8
3MHz
ULV2772 Family Of 2.7V High-Slew-Rate Rail-To-Rail Output Operational  Amplifiers

* Qualified for Automotive or Portable Applications
* High Slew Rate: 10.5V/gs Typ
* High-Gain Bandwidth: 5.1MHz Typ
* Supply Voltage Range from 2.5V ~ 5.5V
* Rail-to-Rail Output
* Input Offset Voltage: 360gV Typ
* Low Distortion Driving 600[: 0.005% THD+N
* Low Supply Current (Per Channel): 1mA
* 17nV/Hz Input Noise Voltage
* 2pA Input Bias Current
* Characterized From TA=−40XC~125XC
2 2.5V~6V 2.7 10.5 TSSOP-8 SOP-8
5.1MHz
LV358 Low Voltage Rail to Rail Output Operational Amplifier

* 2.7V and 5V Performance Guaranteed
* No Crossover Distortion
* 210gA Low Supply Current
* Rail-to-Rail Output Swing @10k[ Load V+ -10mV
                                                          V- +65mV
* VCM From -0.2V to V+ -0.8V
2 2.7V ~ 5.5V 7 1 SOP-8 TSSOP-8 MSOP-8
DFN2030-8
1MHz
L6132 Low Power 10 MHz Rail-to-Rail Input/Output Dual OP,
with Wide Supply Range 2.7V to 24.0V

* 2.7V and 5V Performance Guaranteed
* No Crossover Distortion
* 210gA Low Supply Current
* Rail-to-Rail Output Swing
@10k[ Load V+ -10mV
V +65mV
* VCM From -0.2V to V+ -0.8V
2 2.7V ~ 5.5V 6 1 SOP-8 DFN2020-8
1MHz
L6142* 17 MHz Rail-TO-Rail Input-Output Operatiomal  Amplifiers

* Rail-to-rail Input : -0.25V~5.25V
* Rail-to-Rail Output : 0.005V~4.995V
* Slew Rate:
   Small Signal, 5V/gs
   Large Signal, 30V/gs
* Low Supply Current 650gA/Amplifier
* Wide Supply Range: 1.8V~24V
* Gain 108dB with RL=10k
2 1.8~24V 3.3 25 SOP-8
17MHz
ULV662 50 MHz, RAIL TO RAIL OUTPUT, CMOS DUAL OP AMPS

* Gain Bandwidth Product: 50MHz (typical)
* Short Circuit Current: 90mA (typical)
* Rail-to-Rail Output
* Slew Rate: 32V/gs (typical)
* Power Supply: 2.5V~5.5V
* Extended Temperature Range: -40XC~+125XC
2 2.5V~5.5V 1.5 32 SOP-8
MSOP-8
50MHz
ULV7002 1.5V, 0.23gA/CH, Ultralow Power, Rail-to-Rail Input/Output Dual CMOS Operational Amplifier

* Supply Current: 0.23gA/ch typ.
* Operating Voltage: 1.5V~5.5V
* Input Offset Voltage: 3.0mV max.
* Input Bias Current: 1pA typ.
* Rail-to-Rail Input/Output
* CMOS Technology
2 1.5~5.5V 3 0.001 SOP-8
1.1KHz
ULV8542 1.1MHz, 42gA Rail-To-Rail I/O CMOS Dual OP AMPS

* Low Cost
* Operating voltage range:2.1V~ 5.5V
* Low offset voltage:0.8mV Typical
* Very low input bias currents: 0.5pA
* Rail-to-Rail Input and Output
* Unity Gain Stable
* Gain Bandwidth Product: 1.1MHz
2 2.1V~5.5V 3.5 0.8 MSOP-8
1.1MHz
ULV8622 5.5MHZ, Low Voltage Rail-To-Rail I/O CMOS Dual OP AMPS

* Rail-to-Rail Input and Output
* Input Rail: -0.1V~+5.6V with VS=5.5V
* Gain-Bandwidth Product: 5.5MHz
* High Slew Rate: 3.7V/gs
* Operates on 2.0V~5.5V Supplies
* Low Power: 480gA/Amplifier Typical Supply Current
2 2.0V~5.5V 3mV 3.7V/us SOP-8
5.5MHz
Low Voltage Rail to Rail Output Dual Operational  Amplifier 
Part No. Features Number of
Channels 
VCC VOS(mV)  Slew Rate(V/us) Package
Bandwidth Max Typ
ULC272* CMOS PRECISION DUAL OPERATIONAL AMPLIFIERS

* Low Input Offset Voltage Drift
* Wide Range of Supply Voltages Over Specified Temperature Range: -40XC to 85XC...4V to 16V
* Single-Supply Operation
* Common-Mode Input Voltage Range Extends Below the
Negative Rail
* Output Voltage Range Includes Negative Rail
2 4~16V 10mV 4.6 SOP-8
2.2MHz
ULV607* 2.5V TO 6.0V MICROPOWER CMOS OP AMP

* Power Supply Voltage: 2.5V~6.0V
* Low Input Offset Voltage: 950gV (maximum)
* Rail-to-Rail Output
* Low Quiescent Current: 18.7gA (typical)
* Unity-Gain Stable
* No Phase Reversal
2 2.5V ~ 6.0V 950uV 0.08 SOP-8
155KHz
ULV912* RAIL-TO-RAIL INPUT/OUTPUT 8 MHz OPERATIONAL AMPLIFIERS

* Rail-to-rail input and output
* Wide bandwidth
* Unity gain stability
* High output current: 35 mA
* Operating from 2.5 V to 5.5 V
2 2.5V~5.5V 4.5 4.5 SOP-8
8MHz
Low Voltage Rail to Rail Output Quad Operational Amplifier 
Part No. Features Number of
Channels 
VCC VOS(mV)  Slew Rate(V/us) Package
Bandwidth Max Typ
LV2464 Family Of Low-Power Rail-To-Rail Input/Output Operational Amplifiers

* Rail-to-Rail Output Swing
* 48mA Output Drive Capability (VCC=5V)
* Gain Bandwidth Product: 6.4MHz
* Supply Current: 500gA/channel
* Input Offset Voltage: 100gV
* Input Noise Voltage: 11nV/Hz
* Slew Rate: 1.6V/gs
4 2.7V~6.0V 2 1.6 SOP-14
TSSOP-14
6.4MHz
LV324 Low Voltage Rail to Rail Output Operational Amplifier

* 4-Channels Op amps
* Rail-to-Rail Output Swing
* Widely Input Common-Mode Voltage Range
* Low Voltage Operation
* Low Supply Current: Typ.=410gA @ V+ =5V, V-=0V
* Perfect AC characteristics:
   GBW: Typ.=1MHz
   SR: Typ.=1V/gs
   pm: Typ.=60Deg
   Gm: Typ.=10dB.
4 2.7V ~ 5.5V 7 1 SOP-14 TSSOP-14
1.2MHz
ULV724 Low-Power Rail-To-Rail I/O CMOS Quad Operational Amplifiers

* Supply Voltage Range: 2.1V~5.5V
* Input Voltage Range =- 0.1V~+5.6V with VS=5.5V
* Low Supply Current: 1.3mA/Amplifier
* Low offset voltage : 1.5mV Typical
* Rail-to-Rail Input and Output
* High Gain Bandwidth Product: 11MHz
* High Slew Rate: 8.5V/gs
4 2.1V ~ 5.5V 4 8.5 TSSOP-14 SOP-14
11MHz
High Voltage Rail to Rail I/O Operational Amplifier 
Part No. Features Number of
Channels 
VCC VOS(mV)  Slew Rate(V/us) Package
Bandwidth Max Typ
LMH358 Low Power Rail to Rail Output Operational Amplifier

* Operates on 4.5V~16V supplies
* Input common voltage range beyond the rails
* Rail-to-Rail output voltage swing
* Low input offset voltage 3mV (Typical)
* High gain-bandwidth product 4MHz
* Low quiescent current: 500gA per amplifier
* Large DC voltage gain 100dB (Typical)
* High slew rate 1.3V/gs
* Unit-Gain stable
2 4.5V ~ 16V 10 1.3 SOP-8 
4MHz
ULV1546* 20V High Currrent Drive Rail-To-Rail Vcom/Gamma Buffer

* Wide Supply Operation Range +5V~+20V
* Beyond the rails input capability
* Rail-to-rail output swing
* Low supply current, 1.2mA per amplifier (typical)
* Wide bandwidth (unit gain) 30MHz-3dB bandwidth
* 300mA peak output AC current (typ.)
* High slew rate=30V/gs
* Unity-gain stable
4 5V~+20V 15 27 TSSOP-14
28MHz
隔壁呻吟太大少妇受不了_宝宝把腿开大点就不疼了图_宝贝放松这才一根手指_第一次玩交换真实经历
<֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <֩>| <ı> <ı> <ı> <ı> <ı> <ı>